Water Installation

Item wheel wash water recycling 'Aquador' is a closed system of water purification from suspended particles of mineral oil. Recommended for use on construction sites of the city who do not have time connection to utility networks and communications. There are various configuration items washes the wheels, including wheels for winter cleaning. Technical conditions for laying tiles and installation of the pit. When using the facility without welded trestles road plates are placed parallel to each other with a slope inward at an angle of 10 degrees to the horizontal. In the space between them is placed U-shaped channel or groove is concreted with a bias toward pit for drainage. General bias toward the pit 5-10 degrees. Pit dimensions 1.5 * 1.5 * 1.5 concreted.

Can be laid in a half-brick walls, filled the bottom layer is 10 cm Also, instead of concreting, it is possible to use a welded, airtight container (sheet 2,0-2,5 mm). Submersible pump is suspended in a pit so that the distance of the bottom pump was at the height of 15-20 cm from the bottom of the pit. As the silt pit needs to be cleaned. Otherwise, can not exclude the possibility of breakage of blades pump with stones, rinse with plates. CSB Group of Companies has all the necessary documentation to install wheel wash items with a closed cycle Aquador. The principle of operation of the plant working Water Installation of water recycling washing the wheels of trucks designed for water purification from large suspended particles of sand, clay, soil and other contaminants of this nature at this Purified water is returned for reuse.

ProfilerGruntosmesitel

Profiler-gruntosmesitel DS-178 is structurally executed semi-trailer to the tractor K-701 (K-701M). Attachment to the tractor frame by a special tractor units. Semi-pneumatic to go equipped fluid-brakes. The tractor has a creeper with a hydraulic drive enables you to change the operating speed continuously within 1.5-15 m / min. Transport speed of the car matches the transport speed tractor. Rotor, compactors, water pump – hydraulic.

The situation of workers supported by the automatic system Die sinking of one column. The direction of movement is supported by the tractor steering controlled by the control indicator on the remote control in the cab of the same cord Die sinking. equipment machinery: universal working body of the milling rotor blades and cutting teeth for profiling, and mixing the soil and the auger screw winding feathers water supply system in the mixing zone of soil, consisting of a water tank (capacity 4.5 cu. m), water pump, a set of nozzles across the width of the rotor; tamper with the mechanical vibrator vibration directions. Commissioned by the working body can be mounted disc thrower soil, through which excess soil removed during profiling beyond the earth canvas or loading in . subgrade to within 10 mm from the cord Die sinking with the removal of surplus soil on the right side of the curb along the machine, cutting trough to a depth of 200 mm in one or two pass (depending on the type of soil), soil mixing with granular or liquid binders directly on the roadway in one pass, pre-packing of ready mix compactors. Profiling and mixing soil with a binder made universal rotor and screw in two passes on one track.

Technological scheme of the machine with the working body can be shuttle or with a turn at the end of the aisle. The second scheme is preferable as feeding the machine in reverse to the starting position with two hinges (hinge frame of the tractor and the tractor unit) is less effective. When profiling the subgrade screw working Body falls Ram lowest position. The flap, which separates the mixing chamber by the auger, hydraulic cylinders up to the top position. Hydraulic compactors and water systems are turned off. Ground cut milling rotor mounted on the depth of auger blades thrown and the camera is thrown to the side of the screw. When mixing the soil auger mechanism rises to its highest position, throttle omitted, the drive plate compactors and water system go to work. Crushed and ground Mixing Capacity rotor with cement and water leveled the bottom edge of the damper, denser plate compactors, and then ukatyvaetsya pnevmokatkami.

Cable Jacks

Cable Jack – it's lifting mechanism for raising the cable reel on a small height, is used as a device who gives the winding and cabling. The basic principle of the cable jacks: a central hole threaded cable drum axle jack, axle set centering cone or sleeve, podzhimnye shoes moving along the axis of the drum to the cheeks and fixing clip. Racks Cable jack installed on both sides of the drum, providing a working gap between the cheek and a drum rack design (typically 100 mm.), a significant increase in this gap will increase the bending point on the axis, and thus the possibility of breakage. Next aligned with the axis of lodgements and will be involved lifting mechanism, whether it be a pair of helical, hydraulic or lever system. Lifting is carried to an altitude that provides compensation for uneven cheeks drum plus a guaranteed gap between the cheek and the surface, on which stand rack is usually about 50 – 100 mm cable jack main units: the rack, hoist, tool tray, axle. Cable jacks are classified: 1.Po operating principle: Screw the cable jacks – jacks is working on a pair of screw type (screw-nut) at the same time, usually in the process of lifting a cable drum nut rotational motion, and the screw forward. Screw the cable jacks in turn are divided into: push, cable jacks tyanuschie.Gidravlicheskie – it jacks, in which as the hoisting mechanism uses a hydraulic cylinder or hydraulic jack. The rise of the cable drum is accomplished by reciprocating the handle or hydraulic power station domkrata.Rychazhnye cable jacks – jacks is that the rise of the cable drum by means of a lever, the required force develops due to the difference shoulders arms and lodgement with respect to the support. 2.Po lodgement design: from mobile elements – a cable jacks, providing lightweight rotation axis installed on them, used when necessary to provide a low resistance when unwinding the cable, such as lack of lodgement include the inertia of the system, that is when the unwind reel having some speed, because of the large mass, has a decent inertia and as a consequence of long stops, after the removal of the applied efforts; c fixed point set axis. 3.Po design osikabelnye jacks with ball bearings, cable jacks without bearings. Accessory cable reels are Podzhimnye boots on the axle – to avoid move along the axis of the drum during the winding cable centering cone – for smooth and secure the cable unwinding, Wheel bearings – for maximum cable jacks provide the ability to unwind cable to the cable drums of different sizes.

Ways To Protect Your Web Site

The relative ease of publishing information in the vast Web, supported by examples to follow, sooner or later turns out to many visitors to the web temptation to have your own webpage. If the site owner has a certain tenacity, literacy and good taste, and he definitely has something to say or to show the world and role models originally chosen wisely, the light may well come a worthy and worthwhile web project. A regularly updated site has original content copyright is a good chance of eventually becoming a very popular and bring some fame to its creator. True, this is not always the most often are born too hastily concocted pages, uninformative and poorly decorated. Nevertheless, even the potential authors of quality content that can be interest to a broad audience, not the polls geeks, that quite naturally gives rise to certain difficulties when trying to publish their own materials on the web. Often this is because many people do not think about the external design or compliance with technical requirements. The first question that most acutely concerned about those who first created his life: where to place the site, what hosting to choose? Question, certainly important. But first you need to design a website, at least in general terms.

It is important to remember that everything – and the structure of the menu navigation, and appearance of pages, and finally, the choice of hosting – should be subject to specific content, the content of the site. It is important to properly define and design the future of the site and choose, for example, an advanced web hosting with support for a wide range of technology for a tiny site, it is not justified. Even if no content as such, is vitally important to outline some basic idea of the content itself, the meaning of the site, and ideally – a rough plan for future maintenance.

Grinders

Sawn timber – it's all sorts of products, from wood, which is widely used in modern construction and repair. Lumber made from various wood species using specialized equipment (four-sided machines, Planers, Grinders, wood drying chambers, cutters, Planers) and are thus an important quality as environmental friendliness. Use timber does not have harmful effects on humans and the environment, so the timber is widely used at sites as industrial and civil use. Lumber is classified by several parameters: the cross-sectional 1.Po parameters are the following lumber – boards, beams and bars. Most often, these standard-size lumber. 2.Po forest type from which the building is made materials, timber is divided into coniferous, deciduous and valuable timber trees. The most common form of lumber – boards and blocks are classified into five quality classes.

Boards are divided by thick – thick – more than 32 mm, and thin – less than 32 mm. These are timber edging and cuticles pushed. The most common type of lumber on the market – this board unedged. The ends of the planks sawdust or sawdust is partially at all. These boards are often used to install flooring or upholstery, that is, in cases where it is hidden under the outer coating, and its appearance is not the principal. Lumber made from hardwoods woods: birch, oak, ash, aspen, maple, have on the structure of high strength, but the weight of such timber is much greater than the mass of lumber from coniferous trees.

However, such timber provide an excellent environment and pleasant aesthetic perception. Softwood lumber are not a lot of weight, but are highly durable and moisture resistant. The most popular softwood lumber – spruce, and it pine. Softwood lumber in the form of bars have 4 varieties. Wooden beams – a log hewn on all four sides, dried in a ventilated area for a long time, the thickness of which exceeds 100 mm. Dry beam is practically not affected by shrinkage, and is suitable for the construction of almost any object. Building a dry timber is the basis for all other types of timber: planed beams, laminated veneer lumber, shaped beam. Glued timber – this timber, which is made by gluing dried and boards. Planed timber – it is modern and practical timber, which is a solid, sawn from logs and timber vystroganny. Shaped beam-beam is strictly defined shape of the section (profile) and the presence of auxiliary elements, optimizing the assembly.