Item wheel wash water recycling 'Aquador' is a closed system of water purification from suspended particles of mineral oil. Recommended for use on construction sites of the city who do not have time connection to utility networks and communications. There are various configuration items washes the wheels, including wheels for winter cleaning. Technical conditions for laying tiles and installation of the pit. When using the facility without welded trestles road plates are placed parallel to each other with a slope inward at an angle of 10 degrees to the horizontal. In the space between them is placed U-shaped channel or groove is concreted with a bias toward pit for drainage. General bias toward the pit 5-10 degrees. Pit dimensions 1.5 * 1.5 * 1.5 concreted.

Can be laid in a half-brick walls, filled the bottom layer is 10 cm Also, instead of concreting, it is possible to use a welded, airtight container (sheet 2,0-2,5 mm). Submersible pump is suspended in a pit so that the distance of the bottom pump was at the height of 15-20 cm from the bottom of the pit. As the silt pit needs to be cleaned. Otherwise, can not exclude the possibility of breakage of blades pump with stones, rinse with plates. CSB Group of Companies has all the necessary documentation to install wheel wash items with a closed cycle Aquador. The principle of operation of the plant working Water Installation of water recycling washing the wheels of trucks designed for water purification from large suspended particles of sand, clay, soil and other contaminants of this nature at this Purified water is returned for reuse.

Profiler-gruntosmesitel DS-178 is structurally executed semi-trailer to the tractor K-701 (K-701M). Attachment to the tractor frame by a special tractor units. Semi-pneumatic to go equipped fluid-brakes. The tractor has a creeper with a hydraulic drive enables you to change the operating speed continuously within 1.5-15 m / min. Transport speed of the car matches the transport speed tractor. Rotor, compactors, water pump – hydraulic.

The situation of workers supported by the automatic system Die sinking of one column. The direction of movement is supported by the tractor steering controlled by the control indicator on the remote control in the cab of the same cord Die sinking. equipment machinery: universal working body of the milling rotor blades and cutting teeth for profiling, and mixing the soil and the auger screw winding feathers water supply system in the mixing zone of soil, consisting of a water tank (capacity 4.5 cu. m), water pump, a set of nozzles across the width of the rotor; tamper with the mechanical vibrator vibration directions. Commissioned by the working body can be mounted disc thrower soil, through which excess soil removed during profiling beyond the earth canvas or loading in . subgrade to within 10 mm from the cord Die sinking with the removal of surplus soil on the right side of the curb along the machine, cutting trough to a depth of 200 mm in one or two pass (depending on the type of soil), soil mixing with granular or liquid binders directly on the roadway in one pass, pre-packing of ready mix compactors. Profiling and mixing soil with a binder made universal rotor and screw in two passes on one track.

Technological scheme of the machine with the working body can be shuttle or with a turn at the end of the aisle. The second scheme is preferable as feeding the machine in reverse to the starting position with two hinges (hinge frame of the tractor and the tractor unit) is less effective. When profiling the subgrade screw working Body falls Ram lowest position. The flap, which separates the mixing chamber by the auger, hydraulic cylinders up to the top position. Hydraulic compactors and water systems are turned off. Ground cut milling rotor mounted on the depth of auger blades thrown and the camera is thrown to the side of the screw. When mixing the soil auger mechanism rises to its highest position, throttle omitted, the drive plate compactors and water system go to work. Crushed and ground Mixing Capacity rotor with cement and water leveled the bottom edge of the damper, denser plate compactors, and then ukatyvaetsya pnevmokatkami.

Cable Jack – it's lifting mechanism for raising the cable reel on a small height, is used as a device who gives the winding and cabling. The basic principle of the cable jacks: a central hole threaded cable drum axle jack, axle set centering cone or sleeve, podzhimnye shoes moving along the axis of the drum to the cheeks and fixing clip. Racks Cable jack installed on both sides of the drum, providing a working gap between the cheek and a drum rack design (typically 100 mm.), a significant increase in this gap will increase the bending point on the axis, and thus the possibility of breakage. Next aligned with the axis of lodgements and will be involved lifting mechanism, whether it be a pair of helical, hydraulic or lever system. Lifting is carried to an altitude that provides compensation for uneven cheeks drum plus a guaranteed gap between the cheek and the surface, on which stand rack is usually about 50 – 100 mm cable jack main units: the rack, hoist, tool tray, axle. Cable jacks are classified: 1.Po operating principle: Screw the cable jacks – jacks is working on a pair of screw type (screw-nut) at the same time, usually in the process of lifting a cable drum nut rotational motion, and the screw forward. Screw the cable jacks in turn are divided into: push, cable jacks tyanuschie.Gidravlicheskie – it jacks, in which as the hoisting mechanism uses a hydraulic cylinder or hydraulic jack. The rise of the cable drum is accomplished by reciprocating the handle or hydraulic power station domkrata.Rychazhnye cable jacks – jacks is that the rise of the cable drum by means of a lever, the required force develops due to the difference shoulders arms and lodgement with respect to the support. 2.Po lodgement design: from mobile elements – a cable jacks, providing lightweight rotation axis installed on them, used when necessary to provide a low resistance when unwinding the cable, such as lack of lodgement include the inertia of the system, that is when the unwind reel having some speed, because of the large mass, has a decent inertia and as a consequence of long stops, after the removal of the applied efforts; c fixed point set axis. 3.Po design osikabelnye jacks with ball bearings, cable jacks without bearings. Accessory cable reels are Podzhimnye boots on the axle – to avoid move along the axis of the drum during the winding cable centering cone – for smooth and secure the cable unwinding, Wheel bearings – for maximum cable jacks provide the ability to unwind cable to the cable drums of different sizes.